How long does it take to fry a turkey?
Maintain the temperature of the oil at 350 degrees F (175 degrees C), and cook turkey for 3 1/2 minutes per pound, about 45 minutes. Carefully remove basket from oil, and drain turkey. Insert a meat thermometer into the thickest part of the thigh; the internal temperature must be 180 degrees F (80 degrees C).
How long does it take to fry a 15 pound turkey?
Fry the turkey for 3 minutes per pound (455 grams). For a 15 lb (6.8 kg) turkey, this will take 45 minutes. Make sure the oil temp is maintained at 350°F (180°C).
What do I need to fry a turkey?
You’ll need a turkey, peanut oil, propane burner, stock pot, frying basket, temperature gauge, meat thermometer, a rod, an apron, and a fire extinguisher.
When should you inject a turkey before frying?
Traditionally, a fried turkey is injected with a marinade before it’s cooked; how long before cooking is a subject of debate. You can inject the turkey anywhere from 24 hours to 5 minutes before frying. We had good results injecting two hours before frying.
Is frying a turkey healthy?
Unless you eat the skin, there is little difference in calories and fat between the roasted and fried turkey, as long as the fried turkey is cooked in a healthy fat like peanut or canola oil. … Research has also indicated that frying properly also results in moister breast meat, compared to roasting.
Is it dangerous to fry a turkey?
Deep-fat turkey fryers are extremely dangerous because they run a high risk of spilling hot oil, tipping over, and overheating; all of which can lead to burns, fires, and other injuries.
Do you fry a turkey with the lid on or off?
You do this by turning the hose regulator valve (the red one) to the left. Then put the lid on the pot and let the oil heat to 350°F. Lots of fryer pot lids have a hole that you can stick the thermometer right into. Your oil WILL heat without a lid if you don’t have one, it’ll just take longer.
Does Turkey have to be fully submerged in oil?
Measure the Oil Level
To determine how much oil is needed, place the turkey in the fryer pot and fill the pot with water until the turkey is fully submerged with water rising about 2 inches past the bird. Remove the turkey from the pot, pat it dry with paper towels, and set it aside at room temperature.
Do you cook a turkey at 325 or 350?
Roast the turkey uncovered at a temperature ranging from 325°F to 350°F. Higher temperatures may cause the meat to dry out, but this is preferable to temperatures that are too low which may not allow the interior of the turkey to cook to a safe temperature.
Can you fry a turkey in the garage?
To make the Thanksgiving feast as ideal as possible, it is best to avoid using fryers on decks, in garages, or near trees and detached structures. Before cooking, the turkey should be thawed and dry, since cold water mixing into hot oil can cause a fire. … If oil comes into contact with the burner, a fire could start.
Can you fry a turkey in the rain?
Never operate a fryer outdoors in the rain or snow. Place the fryer on a level surface, and avoid moving it once it’s in use. … If you notice the oil is smoking, turn the fryer off. Turn off the burner before lowering the turkey into the oil.
Can you fry a turkey on the stove?
Because of the size of the cooking equipment and the large quantity of oil required, deep-frying a whole turkey should never be attempted indoors. Pieces of turkey meat can be safely deep-fried indoors using traditional equipment such as a small pot on a stove top. … If the oil overheats, it may ignite.
Can I inject my turkey the night before?
Cover the turkey and refrigerate overnight to allow the injected liquid to impart its flavor throughout the layers of meat. Remove the turkey from the refrigerator and allow it to stand at room temperature for approximately 2 hours before cooking.
Is it better to brine or inject a turkey?
While injecting adds more flavor to meat than brining, it isn’t quite as good at keeping the meat moist. You can inject a brine and let it sit overnight, but it’s not quite as effective as soaking the meat. Injecting can also be more work.